Sold Out
Sold Out
Sold Out
Sold Out
New
Sold Out
Brand: PiBot
Model: PIEXT010N21
PiBot Hotend Mount, Fit for PiBot 3D printer and Wade extruder.
1. Two mount hole fit NEMA17 stepper Motor.
2. Two Hot End mount hole (thread-M6-2A) distace: 12mm
3. Block shape: 42x15x9.8 mm..
$7.99
Sold Out
Brand: PiBot
Model: PIMEC010N16
PiBot KFL08 8mm Mounted Block Cast Housing Self-aligning Pillow Bearing..
$6.50
New
Sold Out
Brand: PiBot
Model: PIELE010N05
What is it
Display Controller with 4 keys, LCD-2004 and a TF card reader,
Used for display the Printer status and Print by the TF Card.
Display four rows, 20 characters per line LCD 2004.
Easy for put your brand or name in it by the PiBot Firmware.
How it works
Connect
Conect the lcd ..
$29.99
Sold Out
Brand: PiBot
Model: PIELERMPR02
It is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers..
$9.99
New
Sold Out
Brand: PiBot
Model: PIELE010N03
What is it
Can drive 0 - 4.5A current.
Default Driver Micro-stepping: 1/16.
Used for Nema17 or Nema23.
Free aluminium heat-sink .
Can drive two NEMA 17 for one axis at the same time according to the current value.
How it works
Connect Motor to Motor Driver
Parameters Settin..
$19.99
Sold Out
Brand: PiBot
Model: PIELERMPW05
LCD Device & controller
This panel and RAMPS 1.4 shield will let print your G-Code files from an SD card and show you all informations about current print also live tuning is possible - everything without computer connected.
After connecting this panel into your RAMPS you are totally free of..
$9.99
New
Sold Out
Sold Out
Brand: PiBot
Model: PIMEC010N03
The SC8UU is a convenient product, which is build-in LM8UU and work perfectly coopeeration with the Ø8mm linear shaft.
SC8UU or SCS8UU with 4 fix hole(M4-thread deep 8mm): 24 x 18mm.
Base size: 34 x 30mm..
$2.50
Sold Out
Brand: PiBot
Model: PIMEC010N09
SHF8 8mm Linear Rod Rail Shaft Support FOR XYZ Table CNC Router Mill..
$2.99
New
Sold Out
Brand: PiBot
Model: PIELE016N04
What is it
Used for PiBot Controller Board Rev1.x
Connect Stepper Motor Driver
Specofication
Length: 50cm
Shipping List
Motor Driver Power Cable for 3D Printer Controller Board Rev1.x × 1
..
$3.00
New
Sold Out
Brand: PiBot
Model: PIDSC100N01
What is it
Used for 3D Printer Controller Board Rev1.x
Connect Stepper Motor Driver
Specofication
Length: 50cm
Shipping List
Stepper Driver Signal Cable for Controller Board Rev1.x × 1
..
$2.00
Sold Out
Brand: PiBot
Model: PIMOT010N02
STEPPER MOTOR X 4 + TOSHIBA 6600 Stepper Motor Driver 0 - 4.5A X 4..
$122.99
Sold Out
Brand: PiBot
Model: PIELERAMR01
Description:
This product is a carrier board or breakout board for Allegro's A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection ; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you to operate bipolar st..
$4.99
Sold Out
Brand: PiBot
Model: PIMEC010N08
Product Name : Timing Pulley;Model NO. : XL10T;Tooth Quatity : 10
Pitch : 5.08mm/ 1/5";Center Axle Diameter : 12mm / 0.472";Bore Diameter : 5mm/1/5"
Teeth Width : 11mm / 0.433";Fit Belt Width : 10mm / 2/5" (0.39");Overall Size : 22 x 26mm / 0.866" x 1.02"(D*H)
Material : Alumi..
$4.99
New
Sold Out
Brand: PiBot
Model: PIMEC010N13
Z AXIS COUPLERS (SET OF 2) 5mm x 5mm For Prusa I3 3D Printer..
$5.99
New
Brand: PiBot
Model: PIROB400N01
Meowbit is a card-sized grahical programming video game console designed for teenagers. It contains 1.8' full-color screen, 6 x programmable buttons ,1 x buzzer, built-in light sensor , temperatur sensor, SD card slot (For extenal stoage),multyplayer connector and edge connector. Espcially the edge ..
$38.99
New
-21 %
Pre-Order
Brand: PiBot
Model: PIEKC200N01
Video
What is it
A set of electronics kits for GRBL CNC.
Purpose of designed is easy to connected and used by Beginner, Developer, or Manufacturer.
Long cables with quick connector no need soliding.
With the multiple quick connector you can put the power cables of parallel conneti..
$129.99 $164.99
New
Brand: PiBot
Model: PIISR200B01
What is it
This is a simple way to add a relay to your micro controller or CNC controller. It runs off 5V or 3.3V and most controllers can easily drive it.
The circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges.
It does this by shining lig..
$9.99
New
-24 %
Pre-Order
Brand: PiBot
Model: PIEKD200N01
Videos
What is it
A set of electronics kits for 3D Printer.
Purpose of designed is easy to connected and used by Beginner, Developer, or Manufacturer.
Long cables with quick connector no need soldering.
With the multiple quick connector you can put the power cables of parallel c..
$159.99 $209.99
New
-14 %
Sold Out
Brand: PiBot
Model: PICOB200B01
Video1 Used for CNC
Video2 Used for 3D Printer
What is it
Designed for GRBL CNC and 3D printer. link between your PC and your stepper driver drivers for stepper motors. It uses the USB port which is available on all modern computers and laptops.
Purpose of design..
$59.99 $69.99
New
-35 %
Pre-Order
Brand: PiBot
Model: PIDRB220B01
What is it
A variety style signal supply logic input selectable, which compatible with lots of MCU and other controller board, such as Mach3 USBCNC Raspberry Pi and so on.
Quick connector and Normal connector suitable for hobby and factory.
Wide power input DC 8 - 40V.
Signal supply lo..
$12.99 $19.99