Menu
Your Cart

PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)

PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
-50 %
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
PiBot Stepper Motor Driver Rev2.3 TOSHIBA TB6600 (3.3V 5V or Dgnd logic max Output 4.12 - 4.5A)
  • Stock: In Stock
  • Weight: 0.07kg
  • SKU: PIDRB230B01
1991 samples sold
Product Views: 11965
This offer ends in:
Day
Hour
Min
Sec
$9.99
$19.99

What is it

A variety style signal supply logic input selectable, which compatible with lots of MCU and other controller board, such as Mach3 USBCNC Raspberry Pi and so on.

  • Quick connector and Normal connector suitable for hobby and factory.
  • Wide power input DC 8 - 40V.
  • Signal supply logic in Quick connector (en dir clk "3.3V or 5V") optical isolated to the IC.
  • Signal supply logic in Normal connector (en dir clk dgnd "2V to 6V logic") with high speed direct to IC.
  • Microstepping: 1/1, 1/2A, 1/2B, 1/4, 1/8, 1/16(default).
  • 0 - 4.5A(4.12A) ~ (from Toshiba6600 manual) output current can be accurate set by read the voltage of voltmeter.
  • Diagnosis LED available.
  • Heatsink available.
  • Reserve the M3 M2 M1 TQ input pins for program control.

 

How it works

Input and Output

Normal connector and Quick connector is parallel. ONLY ONE CONNECTOR REQUIRED AT ONE TIME.

input-and-output

 

Micro-stepping Setting

This picture shows how you can change the micro-stepping settings of the driver.

mirco-stepping-setting

 

Output Limit current Adjust

You can approximate the current limit by the position of the marked point on the trimmer. DO NOT EXCEED YOUR MOTOR’S CURRENT RATING.

OR the current limit can be adjusted by measuring VREF and turning the trimmer. Connect the [+] of the voltmeter to VREF and the [-] lead to GND and read the value.

Current Limit = VREF ÷ 0.6801

So for example the Max current is: 2.81V ÷ 0.6801 = 4.1317A

output-limit-current-adjust

 

Connect with PiBot Kits

https://www.pibot.com/image/content/stepper-driver-and-motor-connect.jpg

 

https://www.pibot.com/image/content/multiple-quick-connector.jpg

 

Documents

 

Specification

  • Driver Chip: Toshiba6600
  • Power Input: DC 8 - 40V
  • Supply Logic in Quick Connector: 3.3V or 5V
  • Supply Logic in Easy Connector: 2V to 6V
  • Drive Current: 0 - 4.5A(4.12A)
  • Microstepping: 1/1, 1/2A, 1/2B, 1/4, 1/8, 1/16(default)
  • Size of Driver Board: 53mm × 60mm
  • Hole Diameter: 3mm
  • Mounter Hole: 45mm × 50mm

 

Figure Dimension

lenth-and-width

 

Shipping List

  • PiBot Stepper Motor Driver Rev2.3 × 1


Write a review

Note: HTML is not translated!
Bad Good

Shipping Notification

World Wide Shiping

  • DHL: 5 to 9 days
  • SF-EXPRESS INTERNATIONAL: 10 to 30 days