CNC electronics.
-70 %
Brand: PiBot
Model: PIDRB230B01
What is it
A variety style signal supply logic input selectable, which compatible with lots of MCU and other controller board, such as Mach3 USBCNC Raspberry Pi and so on.
Quick connector and Normal connector suitable for hobby and factory.
Wide power input DC 8 - 40V.
Signal supply lo..
$5.99 $19.99
Ex Tax:$5.99
-27 %
Sold Out
Brand: PiBot
Model: PIEKC230N01
Video firmware is old , please check new
What is it
A set of electronics kits for GRBL CNC.
Purpose of designed is easy to connected and used by Beginner, Developer, or Manufacturer.
Long cables with quick connector no need soliding.
With the multiple quick connector you can put t..
$119.99 $164.99
Ex Tax:$119.99
Sold Out
Brand: PiBot
Model: PIEKC230N02
Video firmware is old, please check new!
What is it
A set of electronics kits for GRBL CNC.
Purpose of designed is easy to connected and used by Beginner, Developer, or Manufacturer.
Long cables with quick connector no need soliding.
With the PiBot Multi-Stepper Motor Driver Board..
$79.99
Ex Tax:$79.99
Sold Out
Brand: PiBot
Model: PIIRB230B01
What is it
This is a simple way to add a relay to your micro controller or CNC controller. It runs off 5V or 3.3V and most controllers can easily drive it.
The circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges.
It does this by shining lig..
$9.99
Ex Tax:$9.99
-29 %
Sold Out
Brand: PiBot
Model: PICOB230B01
Video1 Used for CNC (this video is old firmware, please check new)
Video2 Used for 3D Printer (this video is old firmware, please check new)
What is it
Designed for GRBL CNC and 3D printer.
It uses the USB port which is available on all modern computers and lapto..
$49.99 $69.99
Ex Tax:$49.99
-50 %
Sold Out
Brand: PiBot
Model: PIMDB230B01
What is it
MDRB is a 5 in 1 stepper driver module base board designed to use with popular A4988/DRV8825 or TMC2208 modules.
Configurations to each module are supported such as microstepping or input logic inverting.
Input logic level 3.3V and 5V compatible.
How it works
Application of MDRB ..
$9.99 $19.99
Ex Tax:$9.99
-250x250.jpg "TMC2208 Stepper Motor Driver")
Brand: PiBot
Model: PITMC022N08
What is it
3D Printer Stepper Motor DriverMC2208 V1.2 is an ultra-quiet two-phase stepper motor drive chipcontinuous drive current 1.4Apeak current 2Avoltage range 4.75V-36V256 subdivisionThe flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control..
$3.99
Ex Tax:$3.99
-550x550-250x250.jpg "TMC2225 Stepper Motor Driver")
Brand: PiBot
Model: PITMC022N25
What is it
Logic Voltage : 3.3V-5V1SET include : 1pc TMC2225 Driver, 1PC Heat sinkFeature 1 : tmc2225 driverFeature 2 : motor driver moduleFeature 3 : Replace tmc2208/ tmc2209
Shipping List
TMC2225 × 1..
$3.99
Ex Tax:$3.99
-550x550-250x250.png "A4988 Stepper Motor Driver")
Brand: PiBot
Model: PIAAA049N88
What is it
Parameters:Size: 1.5mmX2mm (for RAMPS, ultimaker or other compatible boards);The drive current: 2A (best to install the heat sink)Segments: 1,1 / 2,1 / 4,1 / 8,1 / 16Manufacturing process: higher SMT placement machine manufacturing, non-manual welding, yield, more stable performance.Appl..
$1.39
Ex Tax:$1.39
-550x550-250x250.jpg "DRV8825 Stepper Motor Driver")
Brand: PiBot
Model: PIDRV088N25
What is it
Description:The DRV8825 stepper motor driver carrier is a breakout board for DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance dro..
$1.69
Ex Tax:$1.69
Brand: PiBot
Model: PILVV087N29
What is it
Dimensions: 1.5mm * 2.0mm (Same with the A4988 and DRV8825)Maximum drive current: 1.5A (Default 0.8A)Operating voltage: 6V-36V, the proposed voltage is 12VSupport subdivisions: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128Product Process: four layer PCB boardIn the 64 subdivision or 128 subd..
$7.39
Ex Tax:$7.39
Brand: PiBot
Model: PIBTP023N01
What is it
HC-05 Bluetooth module support Master and Slave mode, modify by AT commander
Use the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.
Module working voltage 3.3 V.
With LED indicator light, use 150mA and 3.3V regulation chip.
With Configure button, use AT Command Set..
$5.60
Ex Tax:$5.60
Brand: PiBot
Model: PIWFP023N01
What is it
HC-05 Bluetooth module support Master and Slave mode, modify by AT commander
Use the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.
Module working voltage 3.3 V.
With LED indicator light, use 150mA and 3.3V regulation chip.
With Configure button, use AT Command Set..
$5.60
Ex Tax:$5.60
Brand: PiBot
Model: PIMES230B01
What is it
Based on ball bearing snap-action switch (PiBot directly designed and order from the factory).
Used to find the datum point( such as x y z (0,0,0)) or keep movement in intended range.
Suitable for 3D Printer and CNC or other motion controller board.
Apply to Joystick, TV game, Time re..
$2.99
Ex Tax:$2.99
Brand: PiBot
Model: PIOES230B01
What is it
Based on transmission type infrared sensor.
Used to find the datum point( such as x y z (0,0,0)) or keep movement in intended range.
Suitable for 3D Printer and CNC or other motion controller board.
How it works
Connect
Connect to the PiBot controller board via endstop cable..
$2.29
Ex Tax:$2.29
Brand: PiBot
Model: PIESC010N00
What is it
Used for connect the endstops to controller board, you may need 3 or 6.
How it works
Specification
Length: 1000mm
3 pins × 3 pins
Shipping List
Endstop Cable for Controller Board Rev2.x (1000mm) × 1..
$1.50
Ex Tax:$1.50
Brand: PiBot
Model: PIPWC002N00
What is it
Signal Cable used in quick connector make you fast link between the controll board Rev2.0 and driver, or you can use a normal cable replace it by use the normal connector.
Used the Multiple Quick Connector put the power cables of parallel connection together, no need soliding.
The numb..
$0.50
Ex Tax:$0.50
Brand: PiBot
Model: PIMTC001N00
How it works
Specofication
Length: 100mm
4Pins
Shipping List
Stepper Motor Cable for Board Rev2.x (100mm) × 1..
$0.50
Ex Tax:$0.50
Brand: PiBot
Model: PISGC003N00
What is it
Signal Cable used in quick connector make you fast link between the controll board Rev2.0 and driver, or you can use a normal cable replace it by use the normal connector.
The number of your need depend on the number of driver your used.
How it works
Specification
..
$1.00
Ex Tax:$1.00
Brand: PiBot
Model: PIUSC010N00
What is it
USB2.0 Standard Cable
Using environmentally friendly material.
Using the standard of USB 2.0 connector, 24k gold-plated contacts, 99.99% oxygen-free copper wire and the data transfer rates up to 480Mb/s.
Twisted-pair data lines (impedance matching): Minimiz..
$4.50
Ex Tax:$4.50
Showing 1 to 20 of 20 (1 Pages)